Essential Plumber Insights for Bathtub Installation
Essential Plumber Insights for Bathtub Installation
Blog Article
Almost everyone has their personal conception with regards to How to Install a Bathtub.

Installing a bathtub isn't precisely brain surgery, but it does call for solid plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old bath tub with a new one is also a moderately difficult project. If the old bathtub is readily easily accessible, the task can relocate quickly; if you need to open up a wall surface to remove the old tub as well as place the new bath tub, the job is a lot harder. In either situation, the project is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and also embeded in the brand-new one. Make sure you have qualified on your own for the job and fit trying it. Rather than working with a contractor to take control of a halfway-completed task, it is far better to think about employing one before you start. Chances are you may need a specialist plumber to make tube links.
This short article will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently purchased a new bathtub as well as do not need to transform the arrangement of your previous water system pipes.
Your devices as well as material list should make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, after that the first thing you should do is detach the water. After doing so, activate the taps to drain pipes any water staying in the system. The process of eliminating the existing faucets can be fairly problematic as a result of the restricted gain access to that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from transforming throughout this process. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin making sure that the washers remain in area between the tap and the sink. Protect the tap in place with the producer supplied backnut. As soon as the tap is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The previous kind should be connected to the faucet finishes initially, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Bath tub
Making use of the two wooden boards under its feet, place the tub in the required placement. The wooden boards are helpful in uniformly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by checking the level and also readjusting the feet on the bathtub until the level reads level.
To mount faucets, fit all-time low of the outermost flexible tap connector to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Turn on the water and also examine all joints as well as new pipework for leaks and also tighten them if needed. Fill up the tub and additionally examine the overflow outlet and the regular outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the tub ought to wait till the bathtub has been utilized a minimum of once as this will resolve it into its last placement.
Getting ready for the Installation
Firstly, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent pressure on the bathtub.
Fit the adaptable tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you use all of the provided washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom satisfies the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to crack an inflexible seal, creating the water to permeate the wall surface between the bathroom and the tiling, causing problems with moisture and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes as well as cartridges, as well as can sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of drenched paper or soft rope. Remember to constantly fill up the bath tub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can crack rather early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally conveniently offered on the marketplace. It is a good idea to fit the tiles utilizing waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I stumbled upon that article about A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the web. If you appreciated our blog post please remember to pass it around. Thank you for your time. Visit again soon.
Schedule Services Report this page